U-Boot 1.1.3 (Jul 9 2017 - 14:14:05) Board: MediaTek APSoC DRAM: 512 MB Config XHCI 40M PLL ****************************** Software System Reset Occurred ****************************** MediaTek SPI flash driver, SPI clock: 32MHz spi device id: ef 40 19 0 find flash: W25Q256FV ============================================ MediaTek U-Boot Version: 5.0.1.0-6 -------------------------------------------- ASIC MT7621A DualCore (MAC to MT7530 Mode) DRAM_CONF_FROM: Auto-Detection DRAM_TYPE: DDR3 DRAM bus: 16 bit Xtal Mode=3 OCP Ratio=1/3 Flash component: SPI Flash Date:Jul 9 2017 Time:14:14:05 ============================================ icache: sets:256, ways:4, linesz:32, total:32768 dcache: sets:256, ways:4, linesz:32, total:32768 #### The CPU freq = 900 MHZ #### estimate memory size = 512 Mbytes Reset MT7530 set LAN/WAN WLLLL (Re)start USB... USB0: mtk-xhci: init hccr be1c0000 and hcor be1c0020 hc_length 32 Register 300010f NbrPorts 3 Starting the controller USB XHCI 0.96 scanning bus 0 for devices... 2 USB Device(s) found scanning bus for storage devices... 0 Storage Device(s) found No USB Storage found. Upgrade FW failed! Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Enter boot command line interface. 5: Load system code then write to Flash via USB Storage. 6: Load system code then write to Flash via Httpd. 9: Load U-Boot code then write to Flash via TFTP. 0 3: System Boot system code via Flash. ## Checking image at bc050000 ... Image Name: MIPS LEDE Linux-4.4.52 Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 2345461 Bytes = 2.2 MB Load Address: 80001000 Entry Point: 80001000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 80001000) ... ## Giving linux memsize in MB, 512 Starting kernel ... [ 0.000000] Linux version 4.4.52-gnu (dgazineu@olimpo) (gcc version 5.4.0 (LEDE GCC 5.4.0 r20-646beea) ) #0 SMP Wed Jul 5 16:50:03 2017 [ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc) [ 0.000000] MIPS: machine is GB-PC1 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 1c000000 @ 00000000 (usable) [ 0.000000] memory: 04000000 @ 20000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] HighMem [mem 0x0000000010000000-0x0000000023ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000001bffffff] [ 0.000000] node 0: [mem 0x0000000020000000-0x0000000023ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000023ffffff] [ 0.000000] VPE topology {2,2} total 4 [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.000000] PERCPU: Embedded 11 pages/cpu @8148e000 s12800 r8192 d24064 u45056 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130560 [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2 init=/lib/init rootdelay=5 console=ttyS0,57600n8 [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Writing ErrCtl register=00040380 [ 0.000000] Readback ErrCtl register=00040380 [ 0.000000] Memory: 511680K/524288K available (5438K kernel code, 253K rwdata, 1296K rodata, 232K init, 284K bss, 12608K reserved, 0K cma-reserved, 262144K highmem) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:256 [ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0x39a85c9bff6, max_idle_ns: 881590591483 ns [ 0.000000] sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 21474836475000000ns [ 0.000000] Calibrating delay loop... 1332.01 BogoMIPS (lpj=6660096) [ 0.050000] pid_max: default: 32768 minimum: 301 [ 0.050000] Security Framework initialized [ 0.060000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.060000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.070000] Initializing cgroup subsys io [ 0.070000] Initializing cgroup subsys devices [ 0.070000] Initializing cgroup subsys freezer [ 0.080000] Initializing cgroup subsys net_cls [ 0.080000] Initializing cgroup subsys pids [ 0.080000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.080000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.080000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.080000] CPU1 revision is: 0001992f (MIPS 1004Kc) [ 0.130000] Synchronize counters for CPU 1: done. [ 0.140000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.140000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.140000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.140000] CPU2 revision is: 0001992f (MIPS 1004Kc) [ 0.190000] Synchronize counters for CPU 2: done. [ 0.200000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.200000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.200000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.200000] CPU3 revision is: 0001992f (MIPS 1004Kc) [ 0.250000] Synchronize counters for CPU 3: done. [ 0.260000] Brought up 4 CPUs [ 0.260000] devtmpfs: initialized [ 0.260000] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.270000] futex hash table entries: 1024 (order: 3, 32768 bytes) [ 0.270000] xor: measuring software checksum speed [ 0.370000] 8regs : 1420.000 MB/sec [ 0.470000] 8regs_prefetch: 1354.000 MB/sec [ 0.570000] 32regs : 1689.200 MB/sec [ 0.670000] 32regs_prefetch: 1556.800 MB/sec [ 0.670000] xor: using function: 32regs (1689.200 MB/sec) [ 0.670000] pinctrl core: initialized pinctrl subsystem [ 0.680000] NET: Registered protocol family 16 [ 0.710000] pull PCIe RST: RALINK_RSTCTRL = 0 [ 0.930000] release PCIe RST: RALINK_RSTCTRL = 7000000 [ 0.940000] ***** Xtal 40MHz ***** [ 0.940000] release PCIe RST: RALINK_RSTCTRL = 7000000 [ 0.950000] Port 0 N_FTS = 1b105000 [ 0.950000] Port 1 N_FTS = 1b105000 [ 0.950000] Port 2 N_FTS = 1b105000 [ 1.810000] -> 21007f2 [ 1.820000] PCIE0 enabled [ 1.820000] PCIE1 enabled [ 1.820000] PCIE2 enabled [ 1.820000] PCI host bridge /pcie@1e140000 ranges: [ 1.830000] MEM 0x0000000060000000..0x000000006fffffff [ 1.830000] IO 0x000000001e160000..0x000000001e16ffff [ 1.840000] PCI coherence region base: 0x60000000, mask/settings: 0xf0000002 [ 2.050000] raid6: int32x1 gen() 197 MB/s [ 2.220000] raid6: int32x1 xor() 213 MB/s [ 2.390000] raid6: int32x2 gen() 366 MB/s [ 2.560000] raid6: int32x2 xor() 268 MB/s [ 2.730000] raid6: int32x4 gen() 362 MB/s [ 2.900000] raid6: int32x4 xor() 256 MB/s [ 3.070000] raid6: int32x8 gen() 327 MB/s [ 3.240000] raid6: int32x8 xor() 233 MB/s [ 3.240000] raid6: using algorithm int32x2 gen() 366 MB/s [ 3.240000] raid6: .... xor() 268 MB/s, rmw enabled [ 3.250000] raid6: using intx1 recovery algorithm [ 3.250000] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 3.250000] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 3.260000] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 3.260000] SCSI subsystem initialized [ 3.260000] usbcore: registered new interface driver usbfs [ 3.270000] usbcore: registered new interface driver hub [ 3.270000] usbcore: registered new device driver usb [ 3.280000] i2c-mt7621 1e000900.i2c: clock 100KHz, re-start not support [ 3.280000] PCI host bridge to bus 0000:00 [ 3.290000] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] [ 3.290000] pci_bus 0000:00: root bus resource [io 0xffffffff] [ 3.300000] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] [ 3.310000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 3.310000] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000] [ 3.320000] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000] [ 3.330000] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000] [ 3.330000] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000] [ 3.340000] pci 0000:00:02.0: BAR 0: no space for [mem size 0x80000000] [ 3.340000] pci 0000:00:02.0: BAR 0: failed to assign [mem size 0x80000000] [ 3.350000] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff] [ 3.360000] pci 0000:00:01.0: BAR 8: assigned [mem 0x60100000-0x601fffff] [ 3.360000] pci 0000:00:02.0: BAR 8: assigned [mem 0x60200000-0x602fffff] [ 3.370000] pci 0000:00:00.0: BAR 1: assigned [mem 0x60300000-0x6030ffff] [ 3.370000] pci 0000:00:01.0: BAR 1: assigned [mem 0x60310000-0x6031ffff] [ 3.380000] pci 0000:00:02.0: BAR 1: assigned [mem 0x60320000-0x6032ffff] [ 3.390000] pci 0000:00:00.0: BAR 7: no space for [io size 0x1000] [ 3.390000] pci 0000:00:00.0: BAR 7: failed to assign [io size 0x1000] [ 3.400000] pci 0000:00:01.0: BAR 7: no space for [io size 0x1000] [ 3.400000] pci 0000:00:01.0: BAR 7: failed to assign [io size 0x1000] [ 3.410000] pci 0000:00:02.0: BAR 7: no space for [io size 0x1000] [ 3.420000] pci 0000:00:02.0: BAR 7: failed to assign [io size 0x1000] [ 3.420000] pci 0000:01:00.0: BAR 5: assigned [mem 0x60000000-0x600001ff] [ 3.430000] pci 0000:01:00.0: BAR 4: no space for [io size 0x0010] [ 3.430000] pci 0000:01:00.0: BAR 4: failed to assign [io size 0x0010] [ 3.440000] pci 0000:01:00.0: BAR 0: no space for [io size 0x0008] [ 3.440000] pci 0000:01:00.0: BAR 0: failed to assign [io size 0x0008] [ 3.450000] pci 0000:01:00.0: BAR 2: no space for [io size 0x0008] [ 3.460000] pci 0000:01:00.0: BAR 2: failed to assign [io size 0x0008] [ 3.460000] pci 0000:01:00.0: BAR 1: no space for [io size 0x0004] [ 3.470000] pci 0000:01:00.0: BAR 1: failed to assign [io size 0x0004] [ 3.470000] pci 0000:01:00.0: BAR 3: no space for [io size 0x0004] [ 3.480000] pci 0000:01:00.0: BAR 3: failed to assign [io size 0x0004] [ 3.480000] pci 0000:00:00.0: PCI bridge to [bus 01] [ 3.490000] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] [ 3.500000] pci 0000:02:00.0: BAR 5: assigned [mem 0x60100000-0x601001ff] [ 3.500000] pci 0000:02:00.0: BAR 4: no space for [io size 0x0010] [ 3.510000] pci 0000:02:00.0: BAR 4: failed to assign [io size 0x0010] [ 3.510000] pci 0000:02:00.0: BAR 0: no space for [io size 0x0008] [ 3.520000] pci 0000:02:00.0: BAR 0: failed to assign [io size 0x0008] [ 3.520000] pci 0000:02:00.0: BAR 2: no space for [io size 0x0008] [ 3.530000] pci 0000:02:00.0: BAR 2: failed to assign [io size 0x0008] [ 3.540000] pci 0000:02:00.0: BAR 1: no space for [io size 0x0004] [ 3.540000] pci 0000:02:00.0: BAR 1: failed to assign [io size 0x0004] [ 3.550000] pci 0000:02:00.0: BAR 3: no space for [io size 0x0004] [ 3.550000] pci 0000:02:00.0: BAR 3: failed to assign [io size 0x0004] [ 3.560000] pci 0000:00:01.0: PCI bridge to [bus 02] [ 3.560000] pci 0000:00:01.0: bridge window [mem 0x60100000-0x601fffff] [ 3.570000] pci 0000:03:00.0: BAR 5: assigned [mem 0x60200000-0x602001ff] [ 3.580000] pci 0000:03:00.0: BAR 4: no space for [io size 0x0010] [ 3.580000] pci 0000:03:00.0: BAR 4: failed to assign [io size 0x0010] [ 3.590000] pci 0000:03:00.0: BAR 0: no space for [io size 0x0008] [ 3.590000] pci 0000:03:00.0: BAR 0: failed to assign [io size 0x0008] [ 3.600000] pci 0000:03:00.0: BAR 2: no space for [io size 0x0008] [ 3.600000] pci 0000:03:00.0: BAR 2: failed to assign [io size 0x0008] [ 3.610000] pci 0000:03:00.0: BAR 1: no space for [io size 0x0004] [ 3.620000] pci 0000:03:00.0: BAR 1: failed to assign [io size 0x0004] [ 3.620000] pci 0000:03:00.0: BAR 3: no space for [io size 0x0004] [ 3.630000] pci 0000:03:00.0: BAR 3: failed to assign [io size 0x0004] [ 3.630000] pci 0000:00:02.0: PCI bridge to [bus 03] [ 3.640000] pci 0000:00:02.0: bridge window [mem 0x60200000-0x602fffff] [ 3.640000] BAR0 at slot 0 = 0 [ 3.650000] bus=0x0, slot = 0x0 [ 3.650000] BAR0 at slot 1 = 0 [ 3.650000] bus=0x0, slot = 0x1 [ 3.650000] BAR0 at slot 2 = 0 [ 3.660000] bus=0x0, slot = 0x2 [ 3.660000] bus=0x1, slot = 0x0, irq=0x0 [ 3.660000] bus=0x2, slot = 0x1, irq=0x0 [ 3.670000] bus=0x3, slot = 0x2, irq=0x0 [ 3.670000] clocksource: Switched to clocksource GIC [ 3.680000] NET: Registered protocol family 2 [ 3.680000] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 3.680000] TCP bind hash table entries: 2048 (order: 2, 16384 bytes) [ 3.690000] TCP: Hash tables configured (established 2048 bind 2048) [ 3.690000] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 3.700000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 3.700000] NET: Registered protocol family 1 [ 3.710000] RPC: Registered named UNIX socket transport module. [ 3.710000] RPC: Registered udp transport module. [ 3.720000] RPC: Registered tcp transport module. [ 3.720000] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 3.730000] Crashlog allocated RAM at address 0x3f00000 [ 3.740000] VFS: Disk quotas dquot_6.6.0 [ 3.740000] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 3.750000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 3.750000] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 3.760000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 3.770000] async_tx: api initialized (async) [ 3.770000] bounce: pool size: 64 pages [ 3.780000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 3.780000] io scheduler noop registered [ 3.790000] io scheduler deadline registered (default) [ 3.790000] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled [ 3.800000] console [ttyS0] disabled [ 3.800000] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 33, base_baud = 3125000) is a 16550A [ 3.810000] console [ttyS0] enabled [ 3.810000] console [ttyS0] enabled [ 3.810000] bootconsole [early0] disabled [ 3.810000] bootconsole [early0] disabled [ 3.820000] ahci 0000:01:00.0: SSS flag set, parallel bus scan disabled [ 3.830000] ahci 0000:01:00.0: AHCI 0001.0200 32 slots 2 ports 6 Gbps 0x3 impl IDE mode [ 3.830000] ahci 0000:01:00.0: flags: 64bit ncq sntf stag led clo pmp pio slum part ccc sxs [ 3.840000] scsi host0: ahci [ 3.850000] scsi host1: ahci [ 3.850000] ata1: SATA max UDMA/133 abar m512@0x60000000 port 0x60000100 irq 11 [ 3.860000] ata2: SATA max UDMA/133 abar m512@0x60000000 port 0x60000180 irq 11 [ 3.860000] ahci 0000:02:00.0: SSS flag set, parallel bus scan disabled [ 3.870000] ahci 0000:02:00.0: AHCI 0001.0200 32 slots 2 ports 6 Gbps 0x3 impl IDE mode [ 3.880000] ahci 0000:02:00.0: flags: 64bit ncq sntf stag led clo pmp pio slum part ccc sxs [ 3.880000] scsi host2: ahci [ 3.890000] scsi host3: ahci [ 3.890000] ata3: SATA max UDMA/133 abar m512@0x60100000 port 0x60100100 irq 31 [ 3.900000] ata4: SATA max UDMA/133 abar m512@0x60100000 port 0x60100180 irq 31 [ 3.900000] ahci 0000:03:00.0: SSS flag set, parallel bus scan disabled [ 3.910000] ahci 0000:03:00.0: AHCI 0001.0200 32 slots 2 ports 6 Gbps 0x3 impl IDE mode [ 3.920000] ahci 0000:03:00.0: flags: 64bit ncq sntf stag led clo pmp pio slum part ccc sxs [ 3.920000] scsi host4: ahci [ 3.930000] scsi host5: ahci [ 3.930000] ata5: SATA max UDMA/133 abar m512@0x60200000 port 0x60200100 irq 32 [ 3.940000] ata6: SATA max UDMA/133 abar m512@0x60200000 port 0x60200180 irq 32 [ 3.940000] MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error [ 3.950000] spi-mt7621 1e000b00.spi: sys_freq: 160000000 [ 3.950000] m25p80 spi32766.0: using chunked io (size=32) [ 3.960000] m25p80 spi32766.0: w25q256 (32768 Kbytes) [ 3.960000] 4 ofpart partitions found on MTD device spi32766.0 [ 3.970000] Creating 4 MTD partitions on "spi32766.0": [ 3.970000] 0x000000000000-0x000000030000 : "u-boot" [ 3.980000] 0x000000030000-0x000000040000 : "u-boot-env" [ 3.980000] 0x000000040000-0x000000050000 : "factory" [ 3.990000] 0x000000050000-0x000002000000 : "firmware" [ 4.040000] 2 uimage-fw partitions found on MTD device firmware [ 4.040000] 0x000000050000-0x00000028ca35 : "kernel" [ 4.050000] 0x00000028ca35-0x000002000000 : "rootfs" [ 4.050000] mtd: device 5 (rootfs) set to be root filesystem [ 4.060000] 1 squashfs-split partitions found on MTD device rootfs [ 4.060000] 0x000001060000-0x000002000000 : "rootfs_data" [ 4.070000] netif_napi_add() called with weight 128 on device eth%d [ 4.090000] libphy: mdio: probed [ 4.250000] ata3: SATA link down (SStatus 0 SControl 300) [ 4.290000] ata5: SATA link down (SStatus 0 SControl 300) [ 4.410000] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300) [ 4.410000] ata1.00: ATA-9: WDC WDS100T1B0A-00H9H0, X41100WD, max UDMA/133 [ 4.420000] ata1.00: 1953525168 sectors, multi 1: LBA48 NCQ (depth 31/32), AA [ 4.420000] ata1.00: configured for UDMA/133 [ 4.430000] scsi 0:0:0:0: Direct-Access ATA WDC WDS100T1B0A- 00WD PQ: 0 ANSI: 5 [ 4.440000] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB) [ 4.440000] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 4.440000] sd 0:0:0:0: [sda] Write Protect is off [ 4.440000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 4.450000] sda: sda1 sda2 sda3 [ 4.450000] sd 0:0:0:0: [sda] Attached SCSI disk [ 4.720000] mtk_soc_eth 1e100000.ethernet: loaded mt7530 driver [ 4.730000] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 10 [ 4.730000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 4.740000] ehci-pci: EHCI PCI platform driver [ 4.740000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 4.750000] ohci-platform: OHCI generic platform driver [ 4.750000] xhci-mtk 1e1c0000.xhci: xHCI Host Controller [ 4.760000] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1 [ 4.770000] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x00210010 [ 4.770000] xhci-mtk 1e1c0000.xhci: irq 29, io mem 0x1e1c0000 [ 4.780000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 4.790000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.790000] usb usb1: Product: xHCI Host Controller [ 4.800000] usb usb1: Manufacturer: Linux 4.4.52-gnu xhci-hcd [ 4.800000] usb usb1: SerialNumber: 1e1c0000.xhci [ 4.810000] hub 1-0:1.0: USB hub found [ 4.810000] hub 1-0:1.0: 2 ports detected [ 4.810000] xhci-mtk 1e1c0000.xhci: xHCI Host Controller [ 4.820000] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2 [ 4.820000] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 4.830000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 [ 4.840000] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.840000] usb usb2: Product: xHCI Host Controller [ 4.850000] usb usb2: Manufacturer: Linux 4.4.52-gnu xhci-hcd [ 4.850000] usb usb2: SerialNumber: 1e1c0000.xhci [ 4.860000] hub 2-0:1.0: USB hub found [ 4.860000] hub 2-0:1.0: 1 port detected [ 4.870000] usbcore: registered new interface driver usb-storage [ 4.870000] mt7621_wdt 1e000100.wdt: Initialized [ 4.880000] softdog: Software Watchdog Timer: 0.08 initialized. soft_noboot=0 soft_margin=60 sec soft_panic=0 (nowayout=0) [ 4.890000] md: linear personality registered for level -1 [ 4.890000] md: raid0 personality registered for level 0 [ 4.900000] md: raid1 personality registered for level 1 [ 4.900000] md: raid10 personality registered for level 10 [ 4.910000] md: raid6 personality registered for level 6 [ 4.910000] md: raid5 personality registered for level 5 [ 4.910000] md: raid4 personality registered for level 4 [ 4.920000] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com [ 4.930000] sdhci: Secure Digital Host Controller Interface driver [ 4.930000] sdhci: Copyright(c) Pierre Ossman [ 4.940000] sdhci-pltfm: SDHCI platform and OF driver helper [ 4.940000] MTK MSDC device init. [ 4.950000] SET_IOS: CLK(0kHz), BUS(PUSHPULL), BW(1), PWR(UP), VDD(3.30v), TIMING(LEGACY)SET_IOS: CLK(400kHz), BUS(PUSHPULL), BW(1), PWR(ON), VDD(3.30v), TIMING(LEGACY) [ 4.990000] SET_IOS: CLK(0kHz), BUS(PUSHPULL), BW(1), PWR(OFF), VDD(1.50v), TIMING(LEGACY)[ 4.990000] mtk-sd: MediaTek MT6575 MSDC Driver [ 4.990000] NET: Registered protocol family 10 [ 5.000000] NET: Registered protocol family 17 [ 5.000000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 5.000000] 8021q: 802.1Q VLAN Support v1.8 [ 5.000000] hctosys: unable to open rtc device (rtc0) [ 5.020000] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300) [ 5.020000] ata2.00: ATA-9: WDC WD10JPVX-00JC3T0, 01.01A01, max UDMA/133 [ 5.020000] ata2.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA [ 5.020000] ata2.00: configured for UDMA/133 [ 5.020000] scsi 1:0:0:0: Direct-Access ATA WDC WD10JPVX-00J 1A01 PQ: 0 ANSI: 5 [ 5.020000] sd 1:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB) [ 5.020000] sd 1:0:0:0: [sdb] 4096-byte physical blocks [ 5.020000] sd 1:0:0:0: Attached scsi generic sg1 type 0 [ 5.020000] sd 1:0:0:0: [sdb] Write Protect is off [ 5.020000] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 5.080000] Waiting 5 sec before mounting root device... [ 5.130000] usb 1-2: new high-speed USB device number 2 using xhci-mtk [ 5.270000] usb 1-2: New USB device found, idVendor=1a40, idProduct=0101 [ 5.270000] usb 1-2: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 5.280000] usb 1-2: Product: USB 2.0 Hub [ 5.280000] hub 1-2:1.0: USB hub found [ 5.280000] hub 1-2:1.0: 4 ports detected [ 5.310000] sdb: sdb1 [ 5.310000] sd 1:0:0:0: [sdb] Attached SCSI disk [ 5.370000] ata4: SATA link down (SStatus 0 SControl 300) [ 5.580000] mtk_soc_eth 1e100000.ethernet eth0: port 4 link up [ 5.720000] ata6: SATA link down (SStatus 0 SControl 300) [ 5.790000] mtk_soc_eth 1e100000.ethernet eth0: port 0 link up [ 10.100000] md: Waiting for all devices to be available before autodetect [ 10.100000] md: If you don't use raid, use raid=noautodetect [ 10.110000] md: Autodetecting RAID arrays. [ 10.110000] md: Scanned 0 and added 0 devices. [ 10.110000] md: autorun ... [ 10.120000] md: ... autorun DONE. [ 10.120000] VFS: Mounted root (squashfs filesystem) readonly on device 31:5. [ 10.130000] devtmpfs: mounted [ 10.140000] Freeing unused kernel memory: 232K (806d6000 - 80710000) [ 10.180000] random: nonblocking pool is initialized [ 10.560000] Waiting disk spinup and searching for partition GNUBEE-ROOT...done. [ 16.830000] EXT4-fs (sda2): couldn't mount as ext3 due to feature incompatibilities [ 16.840000] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null) [ 16.850000] Partition GNUBEE-ROOT found. Starting... [ 20.970000] systemd[1]: systemd 215 running in system mode. (+PAM +AUDIT +SELINUX +IMA +SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ -SECCOMP -APPARMOR) [ 20.980000] systemd[1]: Detected architecture 'mips'. Welcome to Debian GNU/Linux 8 (jessie)! [ 21.010000] systemd[1]: Set hostname to . [ 21.120000] systemd[1]: Cannot add dependency job for unit dbus.socket, ignoring: Unit dbus.socket failed to load: No such file or directory. [ 21.130000] systemd[1]: Cannot add dependency job for unit display-manager.service, ignoring: Unit display-manager.service failed to load: No such file or directory. [ 21.150000] systemd[1]: Starting Forward Password Requests to Wall Directory Watch. [ 21.150000] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ 21.160000] systemd[1]: Expecting device dev-ttyS0.device... Expecting device dev-ttyS0.device... [ 21.190000] systemd[1]: Starting Remote File Systems (Pre). [ OK ] Reached target Remote File Systems (Pre). [ 21.210000] systemd[1]: Reached target Remote File Systems (Pre). [ 21.210000] systemd[1]: Starting Dispatch Password Requests to Console Directory Watch. [ 21.220000] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ 21.230000] systemd[1]: Starting Paths. [ OK ] Reached target Paths. [ 21.250000] systemd[1]: Reached target Paths. [ 21.250000] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point. [ 21.260000] systemd[1]: Starting Encrypted Volumes. [ OK ] Reached target Encrypted Volumes. [ 21.290000] systemd[1]: Reached target Encrypted Volumes. [ 21.290000] systemd[1]: Starting Swap. [ OK ] Reached target Swap. [ 21.320000] systemd[1]: Reached target Swap. [ 21.320000] systemd[1]: Starting Root Slice. [ OK ] Created slice Root Slice. [ 21.350000] systemd[1]: Created slice Root Slice. [ 21.350000] systemd[1]: Starting User and Session Slice. [ OK ] Created slice User and Session Slice. [ 21.380000] systemd[1]: Created slice User and Session Slice. [ 21.380000] systemd[1]: Starting /dev/initctl Compatibility Named Pipe. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ 21.410000] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe. [ 21.410000] systemd[1]: Starting Delayed Shutdown Socket. [ OK ] Listening on Delayed Shutdown Socket. [ 21.440000] systemd[1]: Listening on Delayed Shutdown Socket. [ 21.440000] systemd[1]: Starting Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 21.470000] systemd[1]: Listening on Journal Socket (/dev/log). [ 21.470000] systemd[1]: Starting udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 21.500000] systemd[1]: Listening on udev Kernel Socket. [ 21.500000] systemd[1]: Starting udev Control Socket. [ OK ] Listening on udev Control Socket. [ 21.530000] systemd[1]: Listening on udev Control Socket. [ 21.530000] systemd[1]: Starting Journal Socket. [ OK ] Listening on Journal Socket. [ 21.560000] systemd[1]: Listening on Journal Socket. [ 21.560000] systemd[1]: Starting System Slice. [ OK ] Created slice System Slice. [ 21.590000] systemd[1]: Created slice System Slice. [ 21.590000] systemd[1]: Starting File System Check on Root Device... Starting File System Check on Root Device... [ 21.650000] systemd[1]: Starting system-getty.slice. [ OK ] Created slice system-getty.slice. [ 21.670000] systemd[1]: Created slice system-getty.slice. [ 21.670000] systemd[1]: Starting system-serial\x2dgetty.slice. [ OK ][ 21.680000] systemd[1]: Created slice system-serial\x2dgetty.slice. Created slice s[ 21.680000] systemd[1]: Starting Increase datagram queue length... ystem-serial\x2dgetty.slice. Starting [ 21.690000] systemd[1]: Started Set Up Additional Binary Formats. Increase datagra[ 21.700000] systemd[1]: Starting udev Coldplug all Devices... m queue length... Starting udev Coldpl[ 21.710000] systemd[1]: Mounting Debug File System... ug all Devices... Mounting Debug File System... [ 21.720000] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... [ 21.760000] systemd[1]: Mounting POSIX Message Queue File System... Mounting POSIX Message Queue File System... [ 21.790000] systemd[1]: Started Create list of required static device nodes for the current kernel. [ 21.790000] systemd[1]: Starting Create Static Device Nodes in /dev... Starting Create Static Device Nodes in /dev... [ 21.820000] systemd[1]: Mounted Huge Pages File System. [ 21.820000] systemd[1]: Starting Slices. [ OK ] Reached target Slices. [ 21.850000] systemd[1]: Reached target Slices. [ OK ] Mounted POSIX Message Queue File System. [ 21.870000] systemd[1]: Mounted POSIX Message Queue File System. [ OK ] Mounted Debug File System. [ 21.890000] systemd[1]: Mounted Debug File System. [ OK ] Started File System Check on Root Device. [ 21.910000] systemd[1]: Started File System Check on Root Device. [ OK ] Started Increase datagram queue length. [ 21.940000] systemd[1]: Started Increase datagram queue length. [ OK ] Started Load Kernel Modules. [ 22.000000] systemd[1]: Started Load Kernel Modules. [ OK ] Started Create Static Device Nodes in /dev. [ 22.020000] systemd[1]: Started Create Static Device Nodes in /dev. [ OK ] Started udev Coldplug all Devices. [ 22.050000] systemd[1]: Started udev Coldplug all Devices. [ 22.110000] systemd[1]: Starting udev Kernel Device Manager... Starting udev Kernel Device Manager... [ 22.200000] systemd[1]: Mounted Configuration File System. [ 22.200000] systemd[1]: Mounted FUSE Control File System. [ 22.210000] systemd[1]: Starting Apply Kernel Variables... [ 22.210000] systemd-udevd[593]: starting version 215 Starting Apply Kernel Variables... [ 22.240000] systemd[1]: Starting Syslog Socket. [ OK ] Listening on Syslog Socket. [ 22.260000] systemd[1]: Listening on Syslog Socket. [ 22.260000] systemd[1]: Starting Sockets. [ OK ] Reached target Sockets. [ 22.290000] systemd[1]: Reached target Sockets. [ 22.290000] systemd[1]: Starting Journal Service... Starting Journal Service... [ OK ] Started Journal Service. [ 22.380000] systemd[1]: Started Journal Service. Starting Remount Root and Kernel File Systems... [ OK ] Started udev Kernel Device Manager. [ 22.410000] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro [ OK ] Started Apply Kernel Variables. [ OK ] Started Remount Root and Kernel File Systems. [ OK ] Found device /dev/ttyS0. [ 22.483223] systemd-fsck[573]: GNUBEE-ROOT: clean, 14741/1097728 files, 204335/4390845 blocks Starting Various fixups to make systemd work better on Debian... Starting Load/Save Random Seed... [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. [ OK ] Reached target Remote File Systems. Starting Trigger Flushing of Journal to Persistent Storage... Starting Create Volatile Files and Directories... Starting Copy rules generated while the root was ro... [ OK ] Started Various fixups to make systemd work better on Debian. [ OK ] Started Load/Save Random Seed. [ OK ] Started Create Volatile Files and Directories. [ OK ] Started Copy rules generated while the root was ro. [ 22.890000] systemd-journald[620]: Received request to flush runtime journal from PID 1 [ OK ] Started Trigger Flushing of Journal to Persistent Storage. Starting Update UTMP about System Boot/Shutdown... Starting LSB: Raise network interfaces.... [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Started LSB: Raise network interfaces.. [ OK ] Reached target Network. [ OK ] Reached target System Initialization. [ OK ] Reached target Timers. [ OK ] Reached target Basic System. Starting Regular background program processing daemon... [ OK ] Started Regular background program processing daemon. Starting OpenBSD Secure Shell server... [ OK ] Started OpenBSD Secure Shell server. Starting /etc/rc.local Compatibility... Starting System Logging Service... Starting Permit User Sessions... [ OK ] Started System Logging Service. [ OK ] Started Permit User Sessions. [ 23.900000] IPv6: eth0.2: IPv6 duplicate address fe80::7aa3:51ff:feab:b85c detected! [ OK ] Started /etc/rc.local Compatibility. Starting Serial Getty on ttyS0... [ OK ] Started Serial Getty on ttyS0. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Started Update UTMP about System Runlevel Changes. Debian GNU/Linux 8 gnubee-pc1.gnubee ttyS0 gnubee-pc1 login: root Password: GnuBee Linux gnubee-pc1.gnubee 4.4.52-gnu #0 SMP Wed Jul 5 16:50:03 2017 mips The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. root@gnubee-pc1:~# root@gnubee-pc1:~# wget https://raw.githubusercontent.com/gnubee-git/gnubee-git.github.io/master/debian/debian-modules-install <...> Saving to: 'debian-modules-install' <..> root@gnubee-pc1:~# sh debian-modules-install <..> Saving to: 'modules.4.4.52-gnu.tar.gz' modules.4.4.52-gnu. 100%[=====================>] 6.91M 7.99MB/s in 0.9s 2017-09-21 16:36:36 (7.99 MB/s) - 'modules.4.4.52-gnu.tar.gz' saved [7242702/7242702] ./modules.order ./lib/crc-ccitt.ko <..> ./drivers/ata/libahci.ko root@gnubee-pc1:~#